Seat belt restraint system

-
For maximum restraint system protection, the seat belts must always be used whenever the vehicle is moving.
-
Seat belts are most effective when seatbacks are in the upright position.
-
Children age 13 and under must always be properly restrained in the rear seat. Never allow children to ride in the front passenger seat. If a child over 13 must be seated in the front seat, he/she must be properly belted and the seat should be moved as far back as possible.
-
Never wear the shoulder belt under your arm or behind your back. An improperly positioned shoulder belt can cause serious injuries in a crash.
The shoulder belt should be positioned midway over your shoulder across your collarbone.
-
Never wear a seat belt over fragile objects. If there is a sudden stop or impact, the seat belt can damage it.
-
Avoid wearing twisted seat belts. A twisted belt can't do its job well. In a collision, it could even cut into you. Be sure the belt webbing is straight and not twisted.
-
Be careful not to damage the belt webbing or hardware. If the belt webbing or hardware is damaged, replace it.

Seat belts are designed to bear upon the bony structure of the body, and should be worn low across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided.
Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed.
A slack belt will greatly reduce the protection afforded to the wearer.
Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged. It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious. Belts should not be worn with straps twisted. Each belt assembly must only be used by one occupant; it is dangerous to put a belt around a child being carried on the occupant's lap.

-
No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack.
-
When you fasten the seat belt, be careful not to latch the seat belt in buckles of other seat. It's very dangerous and you may not be protected by the seat belt properly.
-
Do not unfasten the seat belt and do not fasten and unfasten the seat belt repeatedly while driving.This could result in loss of control, and an accident causing death, serious injury, or property damage.
-
When fastening the seat belt, make sure that the seat belt does not pass over objects that are hard or can break easily.
-
Make sure there is nothing in the buckle. The seat belt may not be fastened securely.
Driver's seat belt warning

As a reminder to the driver, the seat belt warning light will illuminate for approximately 6 seconds each time you turn the ignition switch or the ENGINE START/STOP button is in ON regardless of belt fastening and warning chime will sound for approximately 6 seconds each time you turn the ignition switch or the ENGINE START/STOP button is in ON when the belt is unfastened.
If a driver continue not to fasten the seat belt and drive below 20km/h, the warning light will stay illuminated.
If a driver continue not to fasten the seat belt while driving over 20km/h, the seat belt warning chime will sound for approximately 100 seconds and the corresponding warning light will blink.
If a driver unfasten the seat belt while driving below 20km/h, the warning light will stay illuminated.
If a driver unfasten the seat belt while driving over 20km/h, the seat belt warning chime will sound for approximately 100 seconds and the corresponding warning light will blink.
Front passenger's seat belt warning

As a reminder to the front passenger, the front passenger’s seat belt warning lights will illuminate for approximately 6 seconds each time you turn the ignition switch or the ENGINE START/STOP button in ON regardless of belt fastening.
If the front passenger continue not to fasten the seat belt and drive below 20km/h, the warning light will stay illuminated.
If the front passenger continue not to fasten the seat belt while driving over 20km/h, the seat belt warning chime will sound for approximately 100 seconds and the corresponding warning light will blink.
If the front passenger unfasten the seat belt while driving below 20km/h, the warning light will stay illuminated.
If the front passenger unfasten the seat belt while driving over 20km/h, the seat belt warning chime will sound for approximately 100 seconds and the corresponding warning light will blink.
Rear passenger’s seat belt warning (if equipped)

As a reminder to the rear passenger, if the seat belt is not fastened when the ignition switch or ENGINE START/STOP button is turned ON, the seat belt warning light will illuminate for approximately 70 seconds.If the rear passenger continue not to fasten the seat belt and drive below 20km/h, the corresponding warning light will continue to illuminate for approximately 70 seconds. If the rear passenger continue not to fasten the seat belt while driving over 20km/h, the seat belt warning light will illuminate for approximately 70 seconds.If you unfasten the seat belt when you drive under 20km/h, the corresponding warning light will continue to illuminate for approximately 70 seconds If the rear passenger unfasten the seat belt while driving over 20km/h, the seat belt warning chime will sound for approximately 35 seconds and the corresponding warning light will blink.

Riding in an improper position adversely affects the front seat belt warning system. It is important for the driver to instruct the passenger to properly be seated as instructed in this manual.

-
Although the front passenger seat is not occupied, the seat belt warning light will blink or illuminate for 6 seconds.
-
The front passenger's seat belt warning may operate when luggage is placed.
Lap/Shoulder belt
Height adjustment

You can adjust the height of the shoulder belt anchor to maximum comfort and safety.
The height of the adjusting seat belt should not be too close to your neck. Otherwise, you will not be getting the most effective protection. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder near the door and not your neck.
To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appropriate position.
To raise the height adjuster, pull it up (1). To lower it, push it down (3) while pressing the height adjuster button (2).
Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into position.
Improperly positioned seat belts can cause serious injuries in an accident.

-
Verify the shoulder belt anchor is locked into position at the appropriate height. Never position the shoulder belt across your neck or face. Improperly positioned seat belts can cause serious injuries in an accident.
-
After a collision, the seat belt system should be inspected to ensure it is operating normally. Replace any belts that are not functioning appropriately.
To fasten your seat belt:

To fasten your seat belt, pull it out of the retractor and insert the metal tab (1) into the buckle (2). There will be an audible "click" when the tab locks into the buckle.
The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It will also lock if you try to lean forward too quickly.

If you are not able to pull out the seat belt from the retractor, firmly pull the belt out and release it. Then you will be able to pull the belt out smoothly.

You should place the lap belt portion as low as possible and snugly across your hips, not on your waist. If the lap belt is located too high on your waist, it may increase the chance of injury in the event of a collision. Both arms should not be under or over the belt. Rather, one should be over and the other under, as shown in the illustration.

Never wear the seat belt under the arm near the door.
Pull the metal tab (B) and insert it (B) into the buckle (B’). There will be an audible “click” when the tab locks into the buckle. Make sure the belt is not twisted.


When using the rear center seat belt the buckle with the “CENTER” mark must be used.

Always have the mini metal tab(A) inserted into the mini buckle (A’).

If you are not able to pull out the safe-ty belt from the retractor, firmly pull the belt out and release it. After release, you will be able to pull the belt out smoothly.
To release the seat belt:

The seat belt is released by pressing the release button (1) in the locking buckle. When it is released, the belt should automatically draw back into the retractor.
If this does not happen, check the belt to be sure it is not twisted, then try again.


The seat belt should be locked into the buckle on each seat cushion to be properly fastened.
(1) : Rear right seat belt fastening buckle
(2) : Rear center seat belt fastening buckle
(3) : Rear left seat belt fastening buckle


When using the rear center seat belt, the buckle with the “CENTER” mark must be used.

Do not force to lock the left or right seat belt into the center seat belt buckle.
Make sure to lock the rear ceter seat belt into the center seat belt buckle.
If not, the improperly fastened seat belt will not be able to provide protection.
Lap belt (if equipped)

To fasten your seat belt:
To fasten a 2-point static type belt, insert the metal tab (1) into the locking buckle (2). There will be an audible "click" when the tab locks into the buckle. Check to make sure the belt is properly locked and that the belt is not twisted.
With a 2-point static type seat belt, the length must be adjusted manually so it fits snugly around your body. Fasten the belt and pull on the loose end to tighten. The belt should be placed as low as possible on your hips (1), not on your waist. If the belt is too high, it could increase the possibility of your being injured in an accident. When using the rear center seat belt, the buckle with the “CENTER” mark must be used.


To release the seat belt:

When you want to release the seat belt, press the button (1) in the locking Buckle.

The center lap belt latching mechanism is different from those for the rear seat shoulder belts. When fastening the rear seat shoulder belts or the center lap belt, make sure they are inserted into the correct buckles to obtain maximum protection from the seat belt system and assure proper operation.