• Press the Driving Assist button to turn on Smart Cruise Control. The speed will be set to the current speed on the cluster.

• If there is no vehicle in front of you, the set speed will be maintained, but if there is a vehicle in front of you, the speed may decrease to maintain the distance to the vehicle ahead. If the vehicle ahead accelerates, your vehicle will travel at a steady cruising speed after accelerating to the set speed.

NOTICE

If your vehicle speed is between 0~30 km/h (0~20 mph) when you press the Driving Assist button, the set speed will be set to 30 km/h (20 mph).

Each time the Vehicle Distance button is pressed, the Vehicle Distance changes as follows:

NOTICE

• If you drive at 90 km/h (56 mph), the distance is maintained as follows:

  • Distance 4 - approximately 52.5 m (172 ft.)

  • Distance 3 - approximately 40 m (130 ft.)

  • Distance 2 - approximately 32.5 m (106 ft.)

  • Distance 1 - approximately 25 m (82 ft.)

• The distance is set to the last set distance when the engine is restarted, or when Smart Cruise Control was temporarily cancelled.

• Push up the + switch, and release it immediately. The set speed will increase by 1 km/h (1 mph) each time the switch is operated in this manner.

• Push up the + switch, and hold it whilst monitoring the set speed on the cluster. The set speed will increase by 10 km/h or 5 mph each time the switch is operated in this manner. Release the switch when the desired speed is shown, and the vehicle will accelerate to that speed. You can increase the set speed to 160 km/h (100 mph).

WARNING

Check the driving condition before using the + switch. Driving speed may sharply increase when you push up and hold the + switch.

• Push down the - switch, and release it immediately. The set speed will decrease by 1 km/h (1 mph) each time the switch is operated in this manner.

• Push down the - switch, and hold it whilst monitoring the set speed on the cluster. The set speed will decrease by 10 km/h or 5 mph each time the switch is operated in this manner.

• Release the switch at the speed you want to maintain. You can decrease the set speed to 30 km/h (20 mph).

Press the switch or depress the brake pedal to temporarily cancel Smart Cruise Control.

To resume Smart Cruise Control after the function was cancelled, operate the +, - or switch.

If you push the + switch up or - switch down, vehicle speed will be set to the current speed on the cluster.

If you press the switch, vehicle speed will resume to the preset speed.

WARNING

Check the driving condition before press the switch. Driving speed may sharply increase or decrease when you press the switch.

Press the Driving Assist button to turn Smart Cruise Control off.

NOTICE

If your vehicle is equipped with Manual Speed Limit Assist, press and hold the Driving Assist button to turn off Smart Cruise Control. However Manual Speed Limit Assist will turn on.

Smart Cruise Control will change acceleration based on the drive mode selected from Drive Mode Integrated Control system. Refer to the following chart.

NOTICE

• For more details on drive mode, refer to More Details.

• Smart Cruise Control may not turn on or off in some of the drive modes for the operating conditions are not satisfied.

• If your vehicle is not equipped with Drive Mode Integrated Control system, Smart Cruise Control accelerates your vehicle at a standard level.

You can adjust the Warning Methods with the ignition switch or ENGINE START/STOP button in the ON position.

• Warning Volume: Select ‘User Settings → Driver Assistance → Warning Volume’ on the LCD display or ‘Settings → Vehicle → Driver Assistance → Warning Methods’ on the Infotainment system.

• Haptic warning: Select 'User settings → Driver assistance → Haptic warning' on the instrument cluster or select 'Settings → Vehicle → Driver assistance → Warning methods → Haptic warning' on the infotainment system, and set the steering wheel vibration warning. (if equipped)

• Driving Safety Priority : Select ‘Settings → Vehicle → Driver Assistance → Warning Methods → Driving Safety Priority’ on the Infotainment system. For safe driving, the audio volume will temporarily decrease to warn the driver with the audible warning.

NOTICE

• Ensure that Warning Methods you have set may apply to the warning volume of other Driver Assistance systems.

• Warning Methods will maintain its last setting even if the vehicle is restarted.

• The setting menu may not be available for your vehicle depending on the vehicle features and specifications.

• With the warning volume is 0, if you deselect Haptic warning, the warning volume will be automatically adjusted with volume 2.

• With the Haptic warning is deselected, if you adjust the warning volume to 0, the Haptic warning will be automatically selected.