Your vehicle is equipped with both left-hand and right-hand outside rear view mirrors.

Be sure to adjust the mirror angles before driving.

The mirrors can be adjusted remotely with the remote switch. The mirror heads can be folded back to prevent damage during an automatic car wash or when passing through a narrow street.

CAUTION

Rear View Mirrors

Do not scrape ice off the mirror face; this may damage the surface of the glass. If ice restricts the movement of the mirror, do not force the mirror for adjustment. To remove ice, use a de-icer spray, a sponge or soft cloth with very warm water or move the vehicle to a warm place and allow the ice to melt.

WARNING

Mirror Adjustment

Do not adjust or fold the outside rear view mirrors while the vehicle is moving. This could result in loss of control.

Adjusting the rear view mirrors:

1. Move the R or L switch (1) to select the right or left side mirror.

2. Press a corresponding point on the mirror adjustment control (2) to position the selected mirror up, down, left or right.

3. After adjustment, put the button into neutral (center) position to prevent inadvertent adjustment.

CAUTION

• The mirrors stop moving when they reach the maximum adjusting angles, but the motor continues to operate while the switch is pressed. Do not press the switch longer than necessary as the motor may be damaged.

• Do not attempt to adjust the outside rear view mirror by hand. Doing so may damage their parts.

Press the outside rear view mirror folding button to fold or unfold the mirror.

The mirror will fold or unfold automatically as follows:

• The mirror will fold or unfold when the door is locked or unlocked by the smart key.

• The mirror will fold or unfold when the door is locked or unlocked by the button on the outside door handle.

• The mirror will unfold when you approach the vehicle (all doors closed and locked) with a smart key in possession (if equipped).

CAUTION

The outside rear view mirror operates even though the EV button is in OFF position. To prevent unnecessary battery discharge, do not adjust the mirrors longer than necessary while the EV button is ON.

Do not fold an outside rear view mirror by hand as this could cause motor failure.

When you shift the gear to the R (Reverse) position, the outside rearview mirrors will rotate downwards to aid with driving in reverse.

The position of the outside rear view mirror switch (1) determines whether the mirrors will move:

Left/Right: When either the L (Left) or R (Right) switch is selected, the corresponding outside rear view mirrors will move.

Neutral: When neither switch is selected, the outside rear view mirrors will not move.

The outside rear view mirrors will automatically revert to their original positions if any of the following occur:

• The ignition switch or EV button is placed to either the LOCK/OFF position or the ACC position.

• The gear is shifted to any position except R (Reverse).

• The remote control outside rear view mirror switch is not selected.

If you don’t have enough visibility with the angles as the factory default conditions, you can readjust and store the angles of outside rear view mirrors.

The factory default angles of the right and left rear view mirrors might be set differently to improve visibility.

1. Set the shifter dial to P (Park). Make sure that the vehicle is stopped and the mirrors are not working.

2. Position the lever to L (left) or R (right) depending on the mirror that you want to adjust.

3. Step on the brake pedal and shift the shifter dial to R (Reverse).

4. When the downward movement of the rearview mirror is finished, adjust the mirror to the desired angle by pressing the switches, ▼, ▲, ◀, ▶.

5. If you shift the dial to a position other than R (Reverse), or change the rearview mirror selector lever to the neutral position and the automatic return of the mirror is finished, the adjusted angle will be automatically saved.

If you want to change the automatic control function of rearview mirrors to the factory default conditions, follow the steps below:

1. Shift the shifter dial to P (Park). Make sure that the vehicle is stopped and the mirrors are not working.

2. Choose the mirror to be adjusted by positioning the lever to L (left) or R (right).

3. Step on the brake pedal and shift the dial to R (Reverse).

4. When the downward movement of the rearview mirror is finished, press the switch ▲ to locate the mirror in the position higher than before (P, N or D).

   (Adjust the mirror in the higher position compared to its position in the driving mode)

5. It is initialized when the dial is shifted to a position other than R (Reverse) or the rearview mirror selector lever is changed to the neutral position. (Initialized position will be applied from the next operation)

CAUTION

We recommend following the procedures in an orderly manner to change or initialize the auto reversing user settings.

If you move to the next step before completing the previous one, the changed angle may not be changed or initialization may not work properly.

The digital side mirror is an outdoor mirror replacement device that helps you change lanes safely by checking the video of the vehicle following you on a monitor inside the vehicle when changing lanes.

DMS Camera

DMS Monitor

WARNING

Do not adjust or fold the DSM camera while driving. It may affect driving and cause an accident.

CAUTION

• Since the DSM displays the rear view as an image, it may look different from the actual view and you cannot see the view outside the set position. Be extra careful when driving.

• The screen of the DSM monitor may be dimmed by direct sunlight, and the monitor screen may be temporarily covered by headlights of a vehicle behind. Use interior mirrors, etc. to secure a view around the vehicle.

• Under certain circumstances, image errors such as out-of-focus or out-of-real colors on the DSM monitor may occur. This makes it difficult to see moving objects clearly, and looking at the monitor for a long time can tire your eyes.

• Always pay attention to the condition of the vehicle while driving. If it is determined that there is something wrong, immediately stop the car and have your vehicle inspected by an authorized Kia dealer.

• If the DSM monitor does not display clearly, the lens may be dirty or fogged up. Moisture on the camera lens is a natural phenomenon caused by external temperature. If you cannot see the rear clearly due to moisture, wipe the camera lens or operate the heating cable to remove moisture or foreign substances before driving safely. Wipe carefully so as not to damage the lens surface, and be careful not to get burned by the heating element.

NOTICE

• DSM monitor screen brightness is also linked to the instrument cluster brightness settings.

• The DSM camera angle also works with the driving position memory system.

When using the turn signal for a lane change, the lane change assist guidance line is displayed on the DSM monitor along with the rear screen.

• Red: Approx. 3 m from the rear of the vehicle

• Orange: Approx. 12 m from the rear of the vehicle

Non-operating condition(s)

• The vehicle is in OFF position.

• Turn signal is off.

• Hazard warning lights are on.

NOTICE

• The lane assist guide line may differ from the actual one depending on the vehicle and road conditions.

• When changing lanes, use the turn signal in advance and enter after checking for sufficient distance in the lane you are entering.

• Select Setup → Vehicle → Lights → Welcome Mirror/Lights → On door unlock from the infotainment system.

• When the door is locked, the mirror will fold.

  • Door lock button on the smart key is pressed

  • Door sensor from the outside door handle is pressed

• When the door is unlocked, the mirror will unfold.

  • Door unlock button on the smart key is pressed

  • Door sensor from the outside door handle is pressed

• Select On door Unlock from the infotainment system to select Auto unlock.

• Carry the smart key and the vehicle mirror will unfold automatically when the key is detected.

CAUTION

• Operation is possible even when the vehicle is turned off, but excessive operation may drain the battery.

• Be sure to use the fold button when folding or unfolding the DSM camera. If you fold or unfold it by hand, the motor may fail. Additionally, the DSM camera may make vibrations or noises while driving, indicating that the gears are not engaged correctly. In this case, engage the gears by folding and unfolding them again with the folding button.

• When cleaning the DSM camera lens or monitor, do not spray the cleaner directly on the lens. Apply it with a soft towel or cloth. If you spray the cleaning agent directly on the DSM camera lens or monitor, the cleaning agent will seep into the lens or monitor and cause a malfunction.

• Do not scrape ice off the surface of the DSM camera lens. Doing so may damage it.

• Do not remove snow or ice from the camera lens with warm or hot water. Cracks may occur on the lens.

• If the DSM camera is frozen and does not move, do not forcibly adjust or fold it. Remove the ice with a de-icing spray or move to a warm place to thaw the ice.

NOTICE

For the safety of the driver, the DSM camera does not fold when driving at speeds of approximately 15 km/h (9 mph) or higher.

When shifting to the R (Reverse) position, the DSM monitor screen can be switched to wide view. When switching to wide view, a guideline is displayed, allowing you to check the parking lines of the vehicle next to you and the side/rear parking lines.

NOTICE

• Guidelines appearing on the DSM monitor when reversing indicate the following points:

  • Approximately 30 cm (12 inches) from the side of the vehicle

  • Approximately 50 cm (20 inches) and approximately 3 ft (1m) from the rear of the vehicle

• When shifting from R (Reverse) to N (Neutral) or driving at a speed of about 10 km/h (6 mph) or more after shifting to D (Drive), the normal view is switched.

• The wide view works only when the DSM monitor screen switching function is used when reversing, and the general view works in P (Parking), N (Neutral), D (Driving) positions.

Operation

• Select L (driver's seat) or R (passenger's seat) with the DSM camera control select switch (1).

• When shifting to the R (Reverse) position, both DSM monitors switch to wide view.

• When the DSM camera control select switch (1) is placed in the center position, both DSM monitors will not switch to wide view.

CAUTION

If there is a problem with the DSM, the screen will not be displayed on the DSM monitor and the warning message ‘Please check DSM system’ will be displayed on the instrument cluster. Check the surroundings with the rear side monitor screen displayed on the cluster and the interior mirror when the turn signal is operated, immediately stop in a safe place, and have your vehicle inspected by an authorized Kia dealer.

• When the vehicle is in ON position, select Setup → Display → Brightness from the infotainment system.

• The brightness can be adjusted automatically or manually.

• Select rear windshield defrosting button when the vehicle is in ON position.